Evroruberoid - the name of bitumen-polymer roofing and waterproofing material to be deposited rolled stekloosnove or polyester.

The production evroruberoidov deposited on a solid footing with the two parties is caused by bitumen or bitumen-polymer mixture, which is covered by a layer on top krupnozernistogo of chips, oil shale, mica or shallow sandy crumbs.

Most thickness of the finished material (3 mm or more) to significantly reduce the number of layers of roofing, compared with Ruberoid. He sticks with the help of propane (a) burner by podplavleniya bottom surface. And do not need any additional equipment for heating and hot adhesive mastics, as required when using roofing. As a result, declining evroruberoid, laying a soft krovlistoimost installation and enhanced safety.
What is the difference between Evroruberoid - from traditional roofing.

In modern evroruberoidnyh material as the basis for using stekloholst, glass fiber fabrics or polyester cloth (polyester).

Stekloholst - the cheapest option. He has a strength comparable with cardboard, but do not decompose. Glass fiber fabrics to 3-5 times stronger than cardboard and stekloholsta, do not decompose and has long service life.

Polyester is as strong as glass fiber fabrics, but has a much higher rate of elongation (40%). It does not decompose and in addition allows for better adhesion to bitumen, which further enhances the quality of the roof.

Traditional evroruberoid based roofing cardboard soaked in bitumen, causing both sides of refractory materials cover composition.

To prevent clumping in roll on both sides bear a dust or fine-grained posypka. Used to the lower strata of roofing carpet rolls of waterproofing construction and for the upper layer of roofing carpet with a protective layer of gravel. Sticks with the help of cold or hot bitumen mastics.

The main criterion for quality evroruberoida - elasticity (with adequate strength).

Achieved through the modification of asphalt weight polymer - styrene-butadiene Styrene (SBS-modified). Modifications provides Fracture (especially with negative temperatures), which is a factor in longevity. It is good bitumen-polymer mass caused by the foundation (stekloholst, glass fiber fabrics or polyester canvas) has a crack, and thus humidity.

Polymer Additives determine the following physical and mechanical properties evroruberoida:

high heat resistance, stability and resilience in the negative temperatures, stability in the abrasion and compression, low deformation under load, compatibility with other roofing materials and concrete.

evroruberoida thickness depends on the amount of bitumen-polymer binder to 1 m . Blvd.

Qualitative indicators evroruberoida:

RUBEROID - waterproof when tested under the pressure of 0001 MPa (0.01 kg / s / c) within 72 hours - does not appear signs of water penetration.

RUBEROID - flexible when tested on Bruce radius of 25 mm at a temperature of +5 ° C - do not appear on the front surface cracks.

rolls are flat ends maximum height of projections of 15 mm.

Roof using roofing made at or below 10 ° C +

tensile breaking strength of not less than 274 (28) H ( kgs)

Teplostoykost roofing + 80 ° C

As such, asphalt is temperature 40-50 OS, that is not enough. Therefore, modern roofing materials used oxidized bitumen. The process of oxidation provides a higher (85-90 OS) level of heat resistance of final product. In doing so, however, reduced frost resistance - material crack at the crease already at a temperature of 0 OS. Moreover, after applying through a process of oxidation bitumen does not stop. The material on this basis, as hold stacked to the roof, over time okislyayutsya even under normal temperatures, which leads to aging material.

To avoid the shortcomings of the oxidized bitumen, it is not oxidizing, and add a special substance Such as ataktichesky polypropylene (APP) and styrene-butadiene-styrene (SBS). This results in very good physical and mechanical characteristics, combined with great longevity (15-25 years).

APP modifier provides high flexibility and heat resistance. In addition to increasing the working temperature range enclosure makes ELTs bitumen resistant to ultraviolet radiation.

Material additives SBS has higher frost resistance and elasticity.

Most producers in Ukraine have the means to install modern technological equipment and acquisition of high-quality plastic.

equipment and technologies used in the manufacture of evroruberoida, are crucial.
Since stir incomplete (no full-scale chemical links) polymer-bitumen, coupled with limited and poor quality polymer leads to a very mediocre performance and the relative fragility evroruberoida. That is «fresh» material is more or less acceptable performance, but the aging process in the flow much faster: after a year it loses all of the initial properties and the roof starts to run.

Today everyone he decides to buy materials European producers, who are certainly good quality, have extremely high prices.

course material with polymer additives expensive than ruberoid. But given the ease of use, high performance and durability that are finished roof would cost even cheaper. And statistics of European countries clearly demonstrates this: evroruberoid used there in 90% of cases.

Bitumen-polymer materials are becoming increasingly popular, and the market in Ukraine.

Choice roof of evroruberoida .

years of research confirms that the quality of the roof is determined not so much the material used, how many construction roofing and the level you accomplish the work of building organizations.

Many manufacturers of modern roofing bitumen-polymer materials reached a high quality and long-govechnosti produced material, but some construction representatives hardly pay attention to the existing new technology and technical solutions to the roof, as well as ensuring their effective professional roofing equipment. In other words, develop ment receive more roofing materials, rather than technology. Therefore, many leading operators about the market makes a further education aimed primarily at the proper use of materials. Gradually, in the domestic construction taking place qualitative changes: improved not only roofing materials, but also technology, engineering tools and techniques work.

In all their diversity bitumosoderzhaschih roll material to a flat roof (of roofing to the bitumen - in limernyh membranes) specialists' advice to apply the bitumen-polymer facing materials to negniyuschey basis, as well as the characteristics of their term of service provided to roofs over 15-20 years.

It is necessary to pay attention to a number of important points if your roof.

• Vapor layer should be made of a long-eternal Water supplies are reliably predotv-raschayuschih hit the water vapor from space in the Tel-insulated and ties. The accumulation of moisture in uteplitele leads to a deterioration of its insulating properties, accumulation
condensate.

• Uteplitel should have the desired design interpretation schinu. Lack of depth will cause isolated kpromerzaniyu roof in winter, the accumulation of condensate, protech-cam in its internal space, mold, pain-Shim teplopoteryam.

• Fill strainer should be done with respect to observe slopes, with no education places stagnant water. The minimum recommended slope for today rolled bitumen-polymer materials deposited 2%. It defined the thickness of modern materials created
place nahlesta neighboring cloth raising the roof to 3-5 mm.

• If your waterproofing carpet should be possible prosushivaniya podkrovelnogo space (to avoid the accumulation of moisture in the insulated-television and the emergence of bubbles on the surface of roofing). To that end, the method of fixing a partial waterproofing carpet to the base. Bitumen-polymer materials are not encouraged to stick Burner mouth-roystvami as overheated often leads to the destruction of these materials and reduces lifespan by 2-3 times.

Organization offering a goods or service

Find "Evroruberoid" in the directory of organizations