"KSAYPEKS concentrate" - powder-based cement, silica sand and a number of special additives.
"KSAYPEKS concentrate" is used to improve waterproofing built and previously built of concrete and reinforced concrete structures.
"KSAYPEKS concentrate" creates a crystallization concrete barrier to prevent water from entering. Jobs' Ksaypeks "based on the principle of diffusion of saturation. However, the pores and capillaries of wet concrete occurs education and tree growth of crystals, which cut across and seal the concrete structure.
In contact with moisture drevovidnye crystals grow steadily within the capillaries, ensuring effective action "KSAYPEKS concentrate" for the entire period of service concrete structures.
most effective application "KSAYPEKS concentrate" is achieved at a temperature of the exploitation of designs ranging from -32 ^{on C to +135 on S. Effectiveness of "KSAYPEKS concentrate" remains at a constant impact of the environment, with pH = 3-11, or the periodic environment from the effects of pH = 2-12.
Humidity and ultraviolet radiation will affect the performance characteristics of concrete, processed "KSAYPEKS concentrate" Processing "KSAYPEKS concentrate" protects the surface of the concrete from chemical aggression of different environments, including chlorides, as well as to prevent the corrosion of reinforcing steel.
"KSAYPEKS concentrate" is not toxic and can be applied to tanks of drinking water and in buildings and facilities the food industry.}

Recommendations for explosives material

Preparation work surface

Before the injury "KSAYPEKS concentrate" to be damp surface must be examined to detect the presence of defects: cavities, the openings of Formwork ties, damaged and unconsolidated construction joints, cracks, areas with "soft" concrete. These zones should be repaired.
The surface must be clean, without peeling, traces Formwork lubricants and other materials. Smooth surface of the concrete from the metal casing or a surface with the remnants of grease or other contaminants must be washed.
Surface of the concrete "old" structures should be cleaned with metal brushes, or 5% solution of hydrochloric acid from a mandatory follow-washing water for withdrawal carbonated layer of concrete and opening capillaries to infiltrate "KSAYPEKS concentrate "
If treatment is provided "KSAYPEKS concentrate" horizontal surfaces of new construction, the surface should not blot out, leaving a little rough. If you'd like to blot out the use of machinery, the processing of reparation should be minimal.
"KSAYPEKS concentrate" in the new structures to better apply immediately after razopalubki designs. The optimum age for treatment of new concrete structures 20 - 72 hours until the concrete still relatively "fresh" and requires only a light moisturizing. Excessive water to the surface "KSAYPEKS concentrate" should be deleted.

Preparation hydraulic mixture to the

"KSAYPEKS concentrate" to shut clean water. At the same time should produce a quantity of the mixture, which can cause within 20 minutes. from the moment zatvoreniya. When zagustevanii mixture, it should be razmeshat without adding water.

Preparation of solutions for causing a brush or spray

"KSAYPEKS concentrate" are mixed with water manually or by using low drills (250 rpm) to the mixing nozzle. Depletion and composition of the mixture depends on the surface roughness.

surface roughness < / td>	Flow "Ksaypeksa "	proportions by volume: "Ksaypeks": water
slightly rough	0.8 kg / m 2	5: 2
Rough	1.1 kg / m 2	3: 1 When causing raspylitelem Depending on the type of equipment and working pressures may require more plastic mixture. Permissible to use the following composition. Depletion material proportions by volume: "Ksaypeks": water 0.8 kg / m 2 5: 3 Mixing dry songs for stopping cavities, seams, cracks and sealing device linear Polusuhaya composition is mixed by hand kelmoy in proportions: 5 parts powder to 1 part water. The duration of mixing: 10-15 seconds. Volume zamesa must conform to the amount of material used within 15 minutes after zatvoreniya Drawing material "KSAYPEKS concentrate" is used at or below 5 on S. working seams. surface of the working seam processing solution "KSAYPEKS concentrate" with the flow rate of 1.1 kg / m 2 . In cases where the installed decking difficult access to shvu working, the seam should be handled "KSAYPEKS concentrate" to install the formwork. When it is not possible, wetting the surface of the working seam sprinkle dry powder "KSAYPEKS concentrate" with the same flow rate. repair defects. Deficient seams and cracks razdelyvayutsya to a depth of at least 2.5 cm and width of 2,0 to 2,5 see high hydrostatic pressure water design depth of cuts - up to 8 cm Razdelanny seam should be thoroughly cleaned and dunk by removing from the excessive water and then processed surface seam solution "KSAYPEKS concentrate" with the flow rate of 0.8 kg / m 2 . After setting the solution on the surface of the seam should be filled repair materials "Ksaypeks plag ". When repairs sinks, caverns and so on, defective zone razdelyvayutsya to healthy concrete. Split surface moisturizes and process solution "KSAYPEKS concentrate". After setting and hardening before the final solution, repaired area is filled with special materials "Ksaypeks plag " Drawing on the surface structures. Solution "KSAYPEKS concentrate 'cause concrete to the surface semi brush or brush volosyanye filling cracks and open pores. For large areas causing appropriate method to produce nabryzga. The distance from the nozzle to the surface should not be too large to guarantee the filling of the hair cracks and then. In some cases, are encouraged to double-cover. The first layer cause "KSAYPEKS concentrate", and the second layer perform "Ksaypeks Modifaytom". He sprayed immediately after setting the first layer coating "KSAYPEKS concentrate". In cases where you want a smooth surface structure, the second coating ( "Ksaypeks Modifayt"), you can overwrite an plane of soft porous material (PU foam, foam rubber, etc.). Care machined surfaces Care treated "KSAYPEKS concentrate 'surface should begin once the material is zatverdel so as not to damage its spraying water (the best treatments is to create a water mist). Treated "KSAYPEKS concentrate" surfaces should be wet three times a day for 2 days or cover this period of damp cloth (sacking). For swimming pools, reservoirs, wells, etc. processed "KSAYPEKS concentrate" surfaces should be wet 3 days, and then endure a period of 12 days before filling the tank. For containers intended for hot or corrosive liquids active treated surfaces should be wet for 3 days and endure for 18 days. When poor air flow (small private reservoirs, wells) required ventilation. Treated surfaces must be protected from wind, sun, rain and temperatures below 2 ° S within 48 hours after causing "KSAYPEKS concentrate". If applied to protect the plastic film, it must lift above the surface, to ensure access of air. Obratnuyu filling should be held not earlier than 36 hours after surface treatment "KSAYPEKS concentrate". If the filling is carried out within 7 days after causing "KSAYPEKS concentrate" material filling should be moist, not to pick up moisture from the mortar caused. "KSAYPEKS concentrates" required 21 days to form crystals, so be white or Protection should be treated surface to withstand the period. Before applying protective coatings processed "KSAYPEKS concentrate 'surface should be neutralized 5% solution of hydrochloric acid, then washed with a strong jet of water.

Find "KSAYPEKS concentrate" in the directory of organizations