KSAYPEKS Patch Plag - single material for hydraulic cement base, modified polymers, including additives for expansion in the hardening and lack of shrinkage, but also dramatically shorten the waiting time setting growth and strength. The strength of the material in 20 minutes. zatvoreniya after 9 MPa. Unlike analog material also includes special chemical additives to penetrate into the pores of the concrete and forming a crystalline structure, make it waterproof. KSAYPEKS Patch Plag does not contain chlorides.

Scope

KSAYPEKS Patch Plag is waterproofing materials and is designed to provide watertight structures of cast and precast concrete and reinforced concrete, as well as stone and brick.
KSAYPEKS Patch Plag be used to create watertight joints As with the exterior, and inside the structure, as well as to eliminate the point and local area leaks.
KSAYPEKS Patch Plag can be used with the same effect as in the construction of new, and in the repair of facilities operated.
KSAYPEKS Patch Plag used for waterproofing construction workers in a range of operating temperatures from minus 50 ^{0 C to +70 0 S.
resulting from KSAYPEKS Patch Plag artificial stone remains corrosion resistance under the influence of liquid media with a measure of activity of hydrogen ions (pH) in the range of 3 to 11.}

^Benefits

Odnokomponentny material, which is just add water. Fast setting: 3 to 4 minutes, with 20 ^{0 C (depending on the consistency of mortar). Excellent structural grip, with the same durability as a stone or concrete, which caused material. Non-metallic, not zarzhaveet and not be destroyed.}

^{Recommendations for explosives material}

KSAYPEKS Patch Plag apply to the ambient temperature of +4 ^{0 C to +30 0 S.}

^{Repair filter cracks, sealing holes.}

^Preparation:

^{There is a need to widen a crack or hole using mechanized tool to a minimum depth of 20 mm square or dovetail, but not in the form of "V " . With the help of a strong jet of water and brush wash away all the loose material and dust from excavation.}

^Mixing:

^{Add 1 part water to 3.5 parts KSAYPEKS Patch Plag volume and mix until a thick consistency of putty. Do not mix more material than could be used for 3 minutes. For best results, water temperature should be about 20 0 S.}

^Zabivka:

^{force, using a light hammer and ram zabeyte KSAYPEKS Patch Plag in the seizure and press down until it induration. Insulation cracks start from top to bottom.}

^{Zabivka with a strong flow of water:}

^{If there are leaks under strong pressure gloved hands make cork and wait until it begins to harden. Then going into the leak, and before the full pressed induration.
In places where a lot of hydrostatic pressure is a large flow of water, drainage outfall would be required to reduce water pressure during the isolation of the surrounding concrete. Proceed as follows:}

1. ^{Using zubila hammer and make recess in the ground water flow.}
2. ^{establish and strengthen a flexible hose or tube part in the seizure, so KSAYPEKS Patch Plag directed the flow of water in the drain. This will reduce the pressure and enable the cause KSAYPEKS Patch Plag on the surrounding concrete. Give 24 hours for drying.}
3. ^{Remove the drain and fill KSAYPEKS Patch Plag in the hole. If necessary, reduce the flow of water by inserting a wooden cork in the rest of the hole before injury KSAYPEKS Patch Plag.}

   ^{If the material KSAYPEKS Patch Plagom can not eliminate the flow of water is recommended to use KSAYPEKS Ultra Plag, who grab for 30 seconds. Add 1 part water to 3 parts KSAYPEKS Ultra Plag (by volume) and quickly peremeshayte to a thick consistency of putty. On the strength vdavite KSAYPEKS Ultra Plag in the seizure and press down until solidification (2-3 min).}

   ^{Installing the patches.}

   ^{For quick repair of concrete or stone masonry, mix KSAYPEKS Patch Plag with clean water until the liquid consistency and working razgladte kelmoy. For large amounts of repair work, mix 1 part KSAYPEKS Patch Plag with 2 parts building sand or stone punctured with a net fraction of 10 mm to a maximum ratio of 18 kg to 27 kg of stones KSAYPEKS Patch Plag.}

   ^{work at elevated temperatures.}

   ^{at temperatures above normal precautions should be taken: water temperature zatvoreniya should not exceed 32 on S. and the material should not be heated to more than 20 on S. Elevated temperatures reduce the time setting material KSAYPEKS Patch Plag. Where possible, materials should be kept under normal temperature conditions.}

   ^{Ankerovka bolts, fittings.}

   ^{Vysverlite hole in the concrete sufficiently deep to secure bolts, fittings, etc. The diameter of the holes must be smaller than the diameter of ankeruemogo part of a 12 - 15 mm for small and medium-sized diameter and 50 mm for large sizes. This is to ensure that the hole left enough space for a solution KSAYPEKS Patch Plaga. Fill the hole solution KSAYPEKS Patch Plagom liquid consistency and vtopite as fixtures or anchor. Outside Condense solution, hold KSAYPEKS Patch Plag wet within 15 minutes. Do not touch the fixtures for 5 hours.}

Organization offering a goods or service

Package Standart+

GSKTB OF INSTITUTE OF PHYSICS OF NAN OF UKRAINE, GP Ukraine, Kyiv region Kiev, pr. Nauki, 46 Views: 173

Find "Ksaypeks patch plag" in the directory of organizations